tag:blogger.com,1999:blog-3025234084286245596.post4918479849076711452..comments2024-03-17T07:15:23.607+00:00Comments on The Making of a Maker: 3D Printer - Comments on 'The Kit'Wisarhttp://www.blogger.com/profile/08937457769749740121noreply@blogger.comBlogger3125tag:blogger.com,1999:blog-3025234084286245596.post-26265192623035087012016-08-26T15:59:41.027+01:002016-08-26T15:59:41.027+01:00I love to read and appreciate your work. eddm prin...I love to read and appreciate your work. <a href="http://www.55printing.com/cheap-every-door-direct-mail-eddm-printing/" rel="nofollow">eddm printer dallas tx</a><br />Sharon Stonehttps://www.blogger.com/profile/06030189084347647504noreply@blogger.comtag:blogger.com,1999:blog-3025234084286245596.post-85189361139064583452014-06-25T07:07:52.741+01:002014-06-25T07:07:52.741+01:00Great Content, I have appreciate with getting lot ...Great Content, I have appreciate with getting lot of good and reliable information with your post .3D printing is creating its mark because it reshapes development and producing and turns people, tiny businesses and company departments into “makers.” CSC’s new report, 3D Printing and therefore the way forward for producing, explores the opportunities of 3D printing services and provides ten queries firms ought to be asking as they prepare to hitch this trend. Click here <a href="http://www.sunruy.com/" rel="nofollow"> Best 3D printer manufacturer company</a> in China. <br /><br />Anonymoushttps://www.blogger.com/profile/06414454429361382744noreply@blogger.comtag:blogger.com,1999:blog-3025234084286245596.post-29542927091950568012014-02-26T04:20:37.958+00:002014-02-26T04:20:37.958+00:00I ordered the same Prusa i3 kit as you from 3D Pri...I ordered the same Prusa i3 kit as you from 3D Printer Czar. I may have even ordered it on the same day as you. Unfortunately, my experience has been much worse. It's interesting that we ordered the same kit on the same day, but what we each received was different. Your kit included a fan; mine did not. My wrench was the right size; yours was not. My smooth Z rods were both about 1 cm too long, so I had to drill the same holes. I also didn't receive the Z couplers and a considerable amount of the nuts, bolts, and washers were not included. Which extruder assembly did you receive? Their site lists Greg's extruder, but I received Wade's extruder.<br /><br />They finally sent me a PDF of their documentation, but it included things like the leveling springs that mine did not. There were a few other things that were different, but I don't remember them off the top of my head.<br /><br />I noticed in the picture of your RAMPS board, you have a red/black wire pair going into the D9 (middle blue) screw terminal. According to the diagram I found for the schematics (http://reprap.org/mediawiki/images/6/6d/Rampswire14.svg), that terminal is used for a 2nd extruder. What did you put in there? Is that for the fan?<br /><br />I think I'm at the point where I try the firmware and calibration, but I can't get Marlin to work at all. It complains about no response from the hot end thermistor. In my experience, thermistors are pretty straightforward with no polarity to worry about, but these thermistors look very similar to diodes, so maybe I'm wrong. It's been a while since I've tested it (I've been waiting on a package from 3D Printer Czar with the missing components), so maybe I didn't check for polarity. The Sprinter firmware does allow me to control motor movements on all 3 axes, but sometimes they just randomly stop working, but that could still be a calibration setting. I can't seem to force the hot end or heat bed to heat up, though.<br /><br />Can you share your configuration file?<br /><br />Thank you for the posts. The pictures are great and it gives me hope of one day getting this thing to print something...anything!<br /><br />Thanks,<br />GarrettGarretthttps://www.blogger.com/profile/09230322443685879512noreply@blogger.com